******
- Verified Buyer
Super simple to pair w Smartthings, just use the Scan for Devices, choose your Hub, and give it really 1 min and it will find Thirdreality devices. You may have to reset these outlets when you get them. I had to reset for 2 of the 4. Works great, 15A! Best price in town for Smartthings outlets.Overall good Zigbee outlets for the price. These are ETL certified for safety and you get 4 units compared to some others that you get only 2 for a similar price. Only thing that I've noticed is that the repeater functionality seems to be of limited range. Still works great overall, but need to space them relatively closer together if you want to take advantage of the Zigbee repeater functionality for non-direct powered devices.So simple to connect. Will see how they fair after a few months.I have a TP link Deco mesh network in my home. I’ve transitioned to a Hubitat for my smart home system.The Third Reality plugs kept getting added to the deco automatically before the Hubitat could pair with them. I had to unplug all of my deco’s, and plug in a wifi router without a smart hub built in to get these to work with my Hubitat. Once I did that, the Hubitat instantly paired with these. Not a flaw with the Third reality, but I wanted to but this out here since it took me many hours to figure this out.These repeat the Zigbee signals which is what we needed most. As controlled sockets go, they work fine.I bought a four-pack of these, and configured three. They are being used to run little table fans in an area of my home that is seldom used, and can get a bit stale. Two of the three configured as Generic Zigbee Outlets and function fine. The third one, as you can see, "thinks" it is a switch.These are being used on a Hubitat Elevation hub, and the Hubitat Community suggested "remove the child device" and then manually set the driver to Generic Zigbee Outlet. All well and good, but the ability to remove it is greyed out.Aside from that, the product seems to be fine. Once I hit Search, they all popped up within a few seconds. They seem to work well. Response is instant.But, three stars for shipping one with odd firmware.EDIT: I DID find a website, and have written their tech support people. Still waiting, but, I sent the email over a weekend. Time will tell.I haven’t had a chance to use these as outlets yet. I just bought them to improve the Zigbee network in a room with lights that didn’t stay connected to the hub. I plugged in three to make a line-of-sight path to the room, then put one in the room itself. Presto—instant reliability. We’ll see how that fourth outlet works with the Xmas tree this winter, but betting it will be fine.I was definitely impressed with the price of these, so I ordered a couple to try out before I ordered more. The first two worked so well, I've since bought two more. I'm pairing these up with ThirdReality motion sensors to control some water fountains and air filters for the cats. When they walk up to the fountain, it starts running for them and shuts off after a couple minutes of no activity. I did the same setup for the air filters around their litter boxes.I like how the device fits on the outlet and leaves plenty of room for something to go in the other plug. A second smart plug would fit there, or any regular power cord. As you can see in the picture, it does partially cover the buttons on a GFCI outlet, but it doesn't interfere with them. If it tripped, I would have to pull the smart plug out to reset the GFCI, but that doesn't happen very often.These (and the motion sensors) were super easy to get added to my Hubitat hub. I haven't found a smart plug that I like better, regardless of the price. And I think these are a bargain at 10 bucks.Very good low cost zigbee plug and repeater that works with Home Assistant Zigbee2MQTT or Deconz. Better than my previous go to, the IKEA plug. This one has a button for manual control, the ikea one does notThe markings on the back show only ETL(us) certified, but if you look up the product code on the ETL directory they are certified against Canadian UL and CSA standards. Just google "ETL certification directory" and put in the product code 3RSP019BZI have purchased a couple four packs of these and they are great. I am using Hubitat and Homebridge to set these up and they are great. Much more reliable than my old iHome wifi plugs.I definitely will be buying more.You can't just buy the plug, if you have google home. It only allows me to setup a hub or a device that looks like a google home but isn't one. No clue if it works as it's incompatible... With one of the most common home devices in the world. #bummed #hadtoreturnJust got into home automation. Decided to try Zigbee and Zwave. Turns out that I prefer zigbee.Using Homeassitant and Zigbee2mqtt these work like a charm and at price for 4 I think these are a steal.Very affordable if you get the 4 pack. Easy to set up with voice command from Echo 4th Gen. All 4 work great so far. Very satisfied. Also own their motion sensor which works great with Alexa routines to turn on lights and make announcements when triggered.
